BJ-550 400MHz-470MHz Full Mode UHF Power Amplifier 5km-10km Walkie Talkie Amp

$219.84 Buy It Now or Best Offer
free,30-Day Returns

Seller Store pincei_us
(2942) 96.5%,

Location: Shenzhen
Ships to: US,
Item: 355323868302

Restocking Fee:No
Return shipping will be paid by:Seller
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money back or replacement (buyer’s choice)
Return policy details:
Frequency range:400MHz – 470MHz
Output power:75W – 85W (typical: 80W); ALC limit
Input power range:0.7W – 7W
Band:UHF
MPN:Does not apply
Bypass power:50W
Unbranded:Unbranded
Type:Power Amplifier
Manufacturer Warranty:2 Years
Modulation:AM, FM, SSB
BJ-550:BJ-550
Features:Full Mode
Country/Region of Manufacture:China

Description BJ-550 400MHz-470MHz Full Mode UHF Power Amplifier SSB 5km-10km Walkie Talkie Amplifier with N-type Connector Usage Mode: – Power measurement: green LED; Bar chart; Not flashing; Output power measurement, increments of 100000 – Power setting display: green LED; Bar chart; flashing; Display the real power limit – SWR measurement: green LED; Point; Not flashing; Display VSWR standing wave ratio – Error prompt: red LED; Point; Not flashing; Display error situations Key Functions: – RX LNA: On/Off Receiver Preamplifier – TX PA: On/Off amplifier transmission power – SSB ON: Switch SSB mode on/off – SET POWER: Display/Change Transmission Power Limit – Show SWR: Enable SWR Turn on/off Amplifier: – The functions of the transmitting power amplifier and the receiving preamplifier are independent of each other. It can be turned on separately by pressing the RX LNA and TX PA buttons. When the corresponding button is pressed, the corresponding LED lights will light up: when all LED lights are off, the machine is completely turned off. Change Power Level: – The transmission power amplifier is equipped with an automatic level control loop, and there are 8 adjustable power levels (10W, 20W… 80W). The first press of “SET POWER” will enter the power preset mode, and the multifunctional display bar will start flashing to display the preset power level. Pressing “SET POWER” for the first time will not change the power level, but will display the actual settings. Continuing to press “SET POWER” will change the power setting. If there is no operation for more than 2 seconds, the machine will exit the power setting mode. – Automatic level control is saturated nonlinear and only applicable to FM modulation. When using AM/SSB modulation with an amplifier, adjust the ALC value to a power of up to 50W, and then adjust the received power to be close to the power displayed on the bar. Do not exceed 10-15W of the downloaded wave power during AM modulation to adapt to no distortion when adjusting to peak. – In SSB adjustment mode, only 50W LED light is on, observe the bar graph in PEP mode. To Turn SSB on/off: – Press “SSB ON” to turn on/off SSB mode, and the actual situation is displayed by the relevant LED lights. When SSB mode is turned on, the carrier sensing algorithm, delay, and power metering bar will be transformed into modulation characteristics. The bias of the power amplifier itself is not different, because this is the inherent linear design of the current design, different from the previous bipolar transistor design. Using External PTT Input: – Place the small socket for connecting the external PTT (external input) on the backplane. It activates TX mode by connecting the central conductor of the socket to the external conductor (ground). Firstly, activate the TX PA function, and the corresponding LED will light up. The amplifier enters external PTT operation mode when it is connected for the first time. The associated LED lights start flashing. – In external PTT mode, the amplifier does not reflect the RF signal input on the walkie talkie. On the contrary, the external PTT signal is already in use every time it is in TX mode. Once SSB mode is enabled, the TX/RX transition delay still exists. The power meter operates in PEP mode. – Unless the TX PA button is pressed or the DC power is unplugged, the amplifier is still in external PTT mode. Measure VSWR (Voltage Standing Wave Ratio): – This practical function can accurately measure the VSWR of the amplifier load. Turn on VSWR measurement and press the SHOW SWR button during transmission. In this mode, the amplifier will remain on for as long as it emits. After releasing the PTT button on the walkie talkie, the display will return to normal operation (power measurement). – The actual VSWR display is a single movement point, with a low value of 1.2, the corresponding LED lights will flash below this value; with a high value of 1.9, and exceeding 2.0, it will cause the corresponding LED lights to flash and indicate out of range. – The built-in high-quality VSWR meter compensates for the non-linearity of the detector, making the test results quite independent in terms of output power. In addition, it can provide additional directionality for the remaining VSWR displayed from 1.10 onwards. Error Signal Explain: – SWR too high: Detection voltage standing wave ratio exceeds (2.). Generally, it is caused by a faulty antenna; At this time, the machine cannot transmit. Please release the PTT key and resume. – Over-gear: Input power exceeding 7W; At this time, the machine cannot transmitting. Release the PTT key and resume. – DC power: DC power supply exceeds the allowable range (10 5-14.8V); At this time, the machine cannot emit. Please release the PTT key and match it with normal voltage before resuming. – High TEMP: The body temperature exceeds 60°C; at this time, the machine cannot emit and can recover after cooling. – PA failure: machine electrical failure; At this time, the machine cannot launch. Release the PTT key and resume. Power Amplifier Specification: – Frequency range: 400MHz – 470MHz – Output power: 75W – 85W (typical: 80W); ALC limit – Input power range: 0.7W – 7W – Input power at full output: 3W – 5W, depend on frequency value – Bypass power: 50W – Harmonic suppression: 63dBc – Modulation: AM, FM, SSB – Circuit type: dual MOSFET, fully push Receiving Preamplifier Specification: – In-band value addition: 13dB – 15.5dB (400 – 470MHz); typical value: 15dB – SNR: 2.4dB – 3dB General Specification: – DC power supply voltage: 10.5V – 14.8V (typ. 12.6V); operating in the low-end range may not be able to generate high power. – Transmitting power supply current: 12A – 13A – Standard power supply current: 20mA: Turn off all functions 35mA: TX function activation 80mA: RX LNA startup 88mA: TX PA and RX LNA start – RF Connector: N-type connector – Product size: 50 x 125 x 210mm – Product weight: 1.15kg Package Included: – 1 x UHF Power Amplifier Payment Terms 1. We accept PayPal,Payoneer,Visa Card,Google pay,Credit card etc. 2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay. Shipping Terms 1. We will process the order within the handling time ,if you have any questions, please contact us via eBay message or email. 2. For remote regions of DHL/FedEx…, extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding. Return Terms If you receive the item that not satisfied or defective, please do not open case and kindly notify us within 30 days. We will guide you the returning process for replacement or refund. Custom Duties & Taxes 1. It is buyer’s responsibility to cover the import duties, taxes.We do not charge any taxes and fees, and the possible taxes and fees will be collected by the platform or by third parties such as customs and carriers. 2. Please check with your country’s customs office and inform us what/how much should declare before shipping. Feedback 1. Please kindly leave us a positive feedback and 5 star DSR if you satisfied with our product and service. Please feel free to contact us firstly if you have any problem with your order, we are responsible and credible seller and will solve the issue it for you asap. 2. If you are dissatisfied for any reason, please don’t be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers. On Dec 27, 2023 at 06:07:10 PST, seller added the following information:

Frequently Asked Questions About BJ-550 400MHz-470MHz Full Mode UHF Power Amplifier 5km-10km Walkie Talkie Amp in My Website

thebusmods.com is the best online shopping platform where you can buy BJ-550 400MHz-470MHz Full Mode UHF Power Amplifier 5km-10km Walkie Talkie Amp from renowned brand(s). thebusmods.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling BJ-550 400MHz-470MHz Full Mode UHF Power Amplifier 5km-10km Walkie Talkie Amp on thebusmods.com?

Frequently Asked Questions About BJ-550 400MHz-470MHz Full Mode UHF Power Amplifier 5km-10km Walkie Talkie Amp in My Website

What are the best-selling BJ-550 400MHz-470MHz Full Mode UHF Power Amplifier 5km-10km Walkie Talkie Amp on thebusmods.com?

Leave a Reply Cancel reply